|
|
发表于 2016-11-8 20:00:38
3555 浏览 2 回复
新拿到的开发板 烧写Linux内核 无限重启问题
编译iTop4412_Kernel_3.0 config_for_linux_scp_elite为zImage
使用otg 只烧的zImage 开发板无限重启
log：
U-Boot 2010.03-dirty (Nov 13 2015 - 02:03:36) for iTOP-4412 Android
APLL = 1000MHz, MPLL = 800MHz
ARM_CLOCK = 1000MHz
PMIC: S5M8767(VER5.0)
Board: iTOP-4412
DRAM: 1 GB
MMC: max_emmc_clock:40 MHZ
Set CLK to 400 KHz
EMMC CLOCK OUTPUT:: 400KHz -[div:50]
response timeout error : 00000104 cmd 8
response timeout error : 00000104 cmd 55
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
MMC0: 3728 MB
SD sclk_mmc is 400K HZ
raise: Signal # 8 caught
raise: Signal # 8 caught
MMC1: 0 MB
0 MB
*** Warning - using default environment
In: serial
Out: serial
Err: serial
eMMC OPEN Success.!!
!!!Notice!!!
!You must close eMMC boot Partition after all image writing!
!eMMC boot partition has continuity at image writing time.!
!So, Do not close boot partition, Before, all images is written.!
MMC read: dev # 0, block # 48, count 16 ...16 blocks read: OK
eMMC CLOSE Success.!!
Checking Boot Mode ... EMMC4.41
SYSTEM ENTER NORMAL BOOT MODE
Hit any key to stop autoboot: 0
reading kernel.. 1120, 12288
MMC read: dev # 0, block # 1120, count 12288 ...12288 blocks read: OK
completed
reading RFS.. 13408, 2048
MMC read: dev # 0, block # 13408, count 2048 ...2048 blocks read: OK
completed
Boot with zImage
## Loading init Ramdisk from Legacy Image at 40df0000 ...
Image Name: ramdisk
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 922119 Bytes = 900.5 kB
Load Address: 40800000
Entry Point: 40800000
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.15 (ms@ubuntu) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #1 SMP PREEMPT Sat Nov 5 22:19:00 PDT 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: SMDK4X12
[ 0.000000] NR_BANKS too low, ignoring high memory
[ 0.000000] **************************
[ 0.000000] reserve_panic_dump_area!!
[ 0.000000] **************************
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU EXYNOS4412 (id 0xe4412011)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] s3c_register_clksrc: clock audiocdclk has no registers set
[ 0.000000] audiocdclk: no parent clock specified
[ 0.000000] s3c_register_clksrc: clock armclk has no registers set
[ 0.000000] EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=350000000
[ 0.000000] EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=24000000
[ 0.000000] ACLK160=160000000, ACLK133=133333333, ACLK100=100000000
[ 0.000000] EXYNOS4: ACLK400=24000000 ACLK266=800000000
[ 0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[ 0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[ 0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[ 0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[ 0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_cam0: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_cam1: source is xusbxti (1), rate is 1500000
。。。
[ 0.000000] sclk_fimd: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_mfc: source is mout_mfc0 (0), rate is 200000000
[ 0.000000] sclk_g3d: source is mout_g3d0 (0), rate is 41666666
[ 0.000000] sclk_pwi: source is xusbxti (1), rate is 1500000
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c0dbb000 s6752 r8192 d13728 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 251650
[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootfstype=ext4 init=/linuxrc console=ttySAC2,115200
[ 0.000000] log_buf_len: 524288
[ 0.000000] early log buf free: 127681(97%)
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 736MB 255MB = 991MB total
[ 0.000000] Memory: 613068k/613068k available, 401716k reserved, 261120K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xfea00000 - 0xffe00000 ( 20 MB)
[ 0.000000] vmalloc : 0xee800000 - 0xf6000000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xee000000 ( 736 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0008000 - 0xc003e000 ( 216 kB)
[ 0.000000] .text : 0xc003e000 - 0xc08cf000 (8772 kB)
[ 0.000000] .data : 0xc08d0000 - 0xc0974e00 ( 660 kB)
[ 0.000000] .bss : 0xc09750f0 - 0xc09b18d0 ( 242 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:456
[ 0.000000] Calibrating delay loop... 1992.29 BogoMIPS (lpj=4980736)
[ 0.045000] pid_max: default: 32768 minimum: 301
[ 0.045000] Mount-cache hash table entries: 512
[ 0.045000] Initializing cgroup subsys debug
[ 0.045000] Initializing cgroup subsys cpuacct
[ 0.045000] Initializing cgroup subsys freezer
[ 0.045000] CPU: Testing write buffer coherency: ok
[ 0.045000] **********panic_dump_test****************
[ 0.045000] There is no valid panic information in memory
[ 0.045000] **************************
[ 0.045000] L310 cache controller enabled
[ 0.045000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x7e470001, Cache size: 1048576 B
[ 0.075000] CPU1: Booted secondary processor
[ 0.095000] CPU2: Booted secondary processor
[ 0.115000] CPU3: Booted secondary processor
[ 0.115000] Brought up 4 CPUs
[ 0.115000] SMP: Total of 4 processors activated (7969.17 BogoMIPS).
[ 0.120000] print_constraints: dummy:
[ 0.120000] NET: Registered protocol family 16
[ 0.120000] value1 = 1, value2 = 0, type = 0x2
[ 0.120000] value1 = 1, value2 = 0, type = 0x2
[ 1.125000] exynos4_pmu_init: PMU supports 4412(96)
[ 1.125000] S3C Power Management, Copyright 2004 Simtec Electronics
[ 1.125000] EXYNOS4: Initializing architecture
[ 1.125000] panic_file create OK !!
[ 1.125000] s3c-adc exynos4412-adc: attached adc driver
[ 1.125000] samsung-pd samsung-pd.0: power domain registered
。。。
[ 1.130000] samsung-pd samsung-pd.7: power domain registered
[ 1.130000] s3c24xx-pwm s3c24xx-pwm.1: tin at 100000000, tdiv at 100000000, tin=divclk, base 8
[ 1.130000] UMP: UMP device driver loaded
[ 1.145000] bio: create slab <bio-0> at 0
[ 1.145000] SCSI subsystem initialized
[ 1.145000] s3c64xx_spi_probe(969)
[ 1.145000] s3c64xx_spi_probe(1092)
[ 1.145000] s3c64xx_spi_probe(1113)
[ 1.150000] usbcore: registered new interface driver usbfs
[ 1.150000] usbcore: registered new interface driver hub
[ 1.150000] usbcore: registered new device driver usb
[ 1.150000] i2c-gpio i2c-gpio.0: using pins 42 (SDA) and 43 (SCL)
[ 1.150000] +s5m8767_pmic_probe()
[ 1.150000] print_constraints: vdd_mif range: 900 <--> 1100 mV at 1100 mV
[ 1.150000] print_constraints: vdd_arm range: 850 <--> 1450 mV at 1200 mV
[ 1.155000] print_constraints: vdd_int range: 875 <--> 1200 mV at 1000 mV
[ 1.155000] print_constraints: vdd_g3d range: 750 <--> 1500 mV at 1100 mV
[ 1.155000] print_constraints: vdd_m12 range: 750 <--> 1500 mV at 1200 mV
[ 1.155000] print_constraints: vdd12_5m range: 750 <--> 1500 mV at 1200 mV
[ 1.155000] print_constraints: vddf28_emmc range: 750 <--> 3000 mV at 2850 mV
[ 7.466793] init: untracked pid 1251 exited
[ 7.471024] init: untracked pid 1252 exited
[ 8.031069] android_usb gadget: high speed config #1: android
[ 8.035581] android_work: sent uevent USB_STATE=CONFIGURED
[ 8.586348] init: untracked pid 1278 exited
[ 9.203678] init: untracked pid 1295 exited
。。。
[ 18.509040] init: untracked pid 1639 exited
[ 22.241936] request_suspend_state: wakeup (3->0) at 22241924220 (2016-11-06 14:30:42.961691425 UTC)
[ 22.253310] init: untracked pid 1247 exited
。。。
[ 23.693441] init: untracked pid 1731 exited
[ 27.611213] request_suspend_state: wakeup (0->0) at 27611204347 (2016-11-06 14:30:48.330972511 UTC)
[ 27.621121] init: untracked pid 1705 exited
[ 27.653029] init: critical process 'servicemanager' exited 4 times in 4 minutes; rebooting into recovery mode
[ 27.688421] SysRq : Emergency Remount R/O
[ 27.714106] EXT4-fs (mmcblk0p3): re-mounted. Opts: (null)
[ 27.729856] EXT4-fs (mmcblk0p4): re-mounted. Opts: (null)
[ 27.740160] Emergency Remount complete
[ 27.791677] REBOOT Notifier for CPUFREQ
[ 27.794036] REBOOT Notifier for BUSFREQ
[ 27.797912] GPS: mt3326_gps_shutdown: Shutting down
[ 27.802723] GPS: mt3326_gps_power: Switching GPS device off
[ 27.808277] GPS: mt3326_gps_power: null pointer!!
[ 27.812970] Mali: Mali shutdown!!
[ 27.816558] s5m-rtc s5m-rtc: s5m_rtc_enable_smpl: disable SMPL
[ 27.823273] s5m_rtc_enable_smpl: WTSR_SMPL(0x00)
[ 27.827776] Restarting system with commaOK
|
|
