iTOP 4412烧录ubuntu出错

dubang12

用16G的高速TF卡按照v2.0的手册进行烧录ubuntu系统。tf卡制作完成后在串口输入reset启动后无法找到emmc的磁盘不能进行不能将ubuntu系统烧录到emmc中去
我的开发板是iTOP4412 scp的
使用的是WIN7 64位的PC和ubuntu的笔记本一起弄的
使用串口和OTG安装android和QTlinux没有问题
在输入df -l后串口返回的数据
root@iTOP4412-ubuntu-desktop:~# df -l
Filesystem     1K-blocks    Used Available Use% Mounted on
/dev/root        2721368 2030984    552144  79% /
none              827200       4    827196   1% /dev
none              165444     672    164772   1% /run
none                5120       0      5120   0% /run/lock
none              827200      24    827176   1% /run/shm输入fdisk -l 串口返回的数据
root@iTOP4412-ubuntu-desktop:~# fdisk -l

Disk /dev/mmcblk0: 15.6 GB, 15634268160 bytes
255 heads, 63 sectors/track, 1900 cylinders, total 30535680 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

        Device Boot      Start         End      Blocks   Id  System
/dev/mmcblk0p1         6791168    30515199    11862016    c  W95 FAT32 (LBA)
/dev/mmcblk0p2           32768     5562367     2764800   83  Linux
/dev/mmcblk0p3         5562368     6176767      307200   83  Linux
/dev/mmcblk0p4         6176768     6791167      307200   83  Linux

Partition table entries are not in disk order

Disk /dev/mmcblk1: 15.9 GB, 15931539456 bytes
255 heads, 63 sectors/track, 1936 cylinders, total 31116288 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

        Device Boot      Start         End      Blocks   Id  System
/dev/mmcblk1p1         5767168    31095807    12664320    c  W95 FAT32 (LBA)
/dev/mmcblk1p2           32768     5562367     2764800   83  Linux
/dev/mmcblk1p3         5562368     5664767       51200   83  Linux
/dev/mmcblk1p4         5664768     5767167       51200   83  Linux

武当山

请问楼主解决问题了吗，我也遇到了ubunto烧写问题，一起交流一下，我QQ710960595

dubang12

OK
  
U-Boot 2010.03 (Dec 23 2014 - 19:09:11) for iTOP-4412 Android
                                                            
        APLL = 1000MHz, MPLL = 800MHz
        ARM_CLOCK = 1000MHz         
PMIC:   S5M8767(VER5.0)   
Board:  iTOP-4412      
DRAM:    2 GB   
MMC:   max_emmc_clock:40 MHZ
Set CLK to 400 KHz         
EMMC CLOCK OUTPUT:: 400KHz -[div:50]
response timeout error : 00000104 cmd 8
response timeout error : 00000104 cmd 55
max_emmc_clock:40 MHZ                  
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz                             
EMMC clock output: 40000 KHz
max_emmc_clock:40 MHZ      
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz                             
EMMC clock output: 40000 KHz
MMC0:   14910 MB            
SD sclk_mmc is 400K HZ
SD sclk_mmc is 50000K HZ
SD sclk_mmc is 50000K HZ
MMC1:   15193 MB        
*** Warning - using default environment
                                       
In:    serial
Out:   serial
Err:   serial
eMMC OPEN Success.!!
                        !!!Notice!!!
!You must close eMMC boot Partition after all image writing!
!eMMC boot partition has continuity at image writing time.!
!So, Do not close boot partition, Before, all images is written.!
                                                                 
MMC read: dev # 0, block # 48, count 16 ...16 blocks read: OK
eMMC CLOSE Success.!!                                       
                     

Checking Boot Mode ... EMMC4.41
SYSTEM ENTER NORMAL BOOT MODE  
Hit any key to stop autoboot:  0
reading kernel.. 1120, 12288     
MMC read: dev # 0, block # 1120, count 12288 ...12288 blocks read: OK
completed                                                            
Boot with zImage
Wrong Ramdisk Image Format
[err] boot_get_ramdisk   
                     
Starting kernel ...
                  
Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0.15 (root@ubuntu) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #5 SMP PREEMPT Fri Apr 10 04:15:07 PDT 2015
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: SMDK4X12
[    0.000000] NR_BANKS too low, ignoring high memory
[    0.000000] **************************
[    0.000000] reserve_panic_dump_area!!
[    0.000000] **************************
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU EXYNOS4412 (id 0xe4412011)
[    0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[    0.000000] s3c_register_clksrc: clock audiocdclk has no registers set
[    0.000000] audiocdclk: no parent clock specified
[    0.000000] s3c_register_clksrc: clock armclk has no registers set
[    0.000000] EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=350000000
[    0.000000] EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=24000000
[    0.000000] ACLK160=160000000, ACLK133=133333333, ACLK100=100000000
[    0.000000] EXYNOS4: ACLK400=24000000 ACLK266=800000000
[    0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[    0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[    0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[    0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[    0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_cam0: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_cam1: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimd: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimd: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_mfc: source is mout_mfc0 (0), rate is 200000000
[    0.000000] sclk_g3d: source is mout_g3d0 (0), rate is 41666666
[    0.000000] sclk_pwi: source is xusbxti (1), rate is 1500000
[    0.000000] PERCPU: Embedded 7 pages/cpu @c19e6000 s6752 r8192 d13728 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 511746
[    0.000000] Kernel command line: console=ttySAC2,115200 root=/dev/mmcblk1p2 init=/linuxrc rootfstype=ext4
[    0.000000] log_buf_len: 524288
[    0.000000] early log buf free: 127676(97%)
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 736MB 1279MB = 2015MB total
[    0.000000] Memory: 1654184k/1654184k available, 409176k reserved, 1309696K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xfea00000 - 0xffe00000   (  20 MB)
[    0.000000]     vmalloc : 0xee800000 - 0xf6000000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xee000000   ( 736 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .init : 0xc0008000 - 0xc003f000   ( 220 kB)
[    0.000000]       .text : 0xc003f000 - 0xc08ef000   (8896 kB)
[    0.000000]       .data : 0xc08f0000 - 0xc0998be0   ( 675 kB)
[    0.000000]        .bss : 0xc099983c - 0xc09d6bd0   ( 245 kB)
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:456
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 1992.29 BogoMIPS (lpj=4980736)
[    0.045000] pid_max: default: 32768 minimum: 301
[    0.045000] Mount-cache hash table entries: 512
[    0.045000] Initializing cgroup subsys debug
[    0.045000] Initializing cgroup subsys cpuacct
[    0.045000] Initializing cgroup subsys freezer
[    0.045000] CPU: Testing write buffer coherency: ok
[    0.045000] **********panic_dump_test****************
[    0.045000] There is no valid panic information in memory
[    0.045000] **************************
[    0.045000] L310 cache controller enabled
[    0.045000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x7e470001, Cache size: 1048576 B
[    0.075000] CPU1: Booted secondary processor
[    0.095000] CPU2: Booted secondary processor
[    0.115000] CPU3: Booted secondary processor
[    0.115000] Brought up 4 CPUs
[    0.115000] SMP: Total of 4 processors activated (7969.17 BogoMIPS).
[    0.120000] print_constraints: dummy:
[    0.120000] NET: Registered protocol family 16
[    0.120000] value1 = 0, value2 = 0, type = 0x0
[    0.120000] sensor_hw_init: line = 306
[    0.160000] exynos4_pmu_init: PMU supports 4412(96)
[    0.160000] S3C Power Management, Copyright 2004 Simtec Electronics
[    0.160000] EXYNOS4: Initializing architecture
[    0.160000] panic_file create OK !!
[    0.160000] s3c-adc exynos4412-adc: attached adc driver
[    0.160000] samsung-pd samsung-pd.0: power domain registered
[    0.160000] samsung-pd samsung-pd.1: power domain registered
[    0.160000] samsung-pd samsung-pd.2: power domain registered
[    0.160000] samsung-pd samsung-pd.5: power domain registered
[    0.160000] samsung-pd samsung-pd.4: power domain registered
[    0.160000] samsung-pd samsung-pd.6: power domain registered
[    0.160000] samsung-pd samsung-pd.7: power domain registered
[    0.160000] s3c24xx-pwm s3c24xx-pwm.1: tin at 100000000, tdiv at 100000000, tin=divclk, base 8
[    0.160000] UMP: UMP device driver  loaded
[    0.180000] bio: create slab <bio-0> at 0
[    0.180000] SCSI subsystem initialized
[    0.180000] s3c64xx_spi_probe(969)
[    0.180000] s3c64xx_spi_probe(1092)
[    0.180000] s3c64xx_spi_probe(1113)
[    0.180000] usbcore: registered new interface driver usbfs
[    0.180000] usbcore: registered new interface driver hub
[    0.180000] usbcore: registered new device driver usb
[    0.185000] i2c-gpio i2c-gpio.0: using pins 42 (SDA) and 43 (SCL)
[    0.185000] +s5m8767_pmic_probe()
[    0.185000] print_constraints: vdd_mif range: 900 <--> 1100 mV at 1100 mV
[    0.185000] print_constraints: vdd_arm range: 850 <--> 1450 mV at 1200 mV
[    0.185000] print_constraints: vdd_int range: 875 <--> 1200 mV at 1000 mV
[    0.185000] print_constraints: vdd_g3d range: 750 <--> 1500 mV at 1100 mV
[    0.190000] print_constraints: vdd_m12 range: 750 <--> 1500 mV at 1200 mV
[    0.190000] print_constraints: vdd12_5m range: 750 <--> 1500 mV at 1200 mV
[    0.190000] print_constraints: vddf28_emmc range: 750 <--> 3000 mV at 2850 mV
[    0.205000] print_constraints: VDDQ_M12: 1500 mV
[    0.205000] print_constraints: VDD18_2M: 1800 mV
[    0.205000] print_constraints: VDD10_MIPI: 1000 mV
[    0.215000] print_constraints: VDD33_LCD: 3300 mV
[    0.220000] print_constraints: VDD18_MIPI: 1800 mV
[    0.230000] print_constraints: VDD33_UOTG: 3300 mV
[    0.235000] print_constraints: VDD10_USH: 1000 mV
[    0.235000] print_constraints: VDD18_HSIC: 1800 mV
[    0.245000] print_constraints: VDDIOPERI_28: 3300 mV
[    0.260000] print_constraints: DC33V_TP: 3300 mV
[    0.260000] print_constraints: VDD28_CAM: 1800 mV

dubang12

[    0.260000] print_constraints: VDD28_AF: 2800 mV
[    0.260000] print_constraints: VDDA28_2M: 2800 mV
[    0.265000] print_constraints: VDD28_TF: 2800 mV
[    0.275000] print_constraints: VDD33_A31: 3300 mV
[    0.295000] print_constraints: VDD18_CAM: 1800 mV
[    0.300000] print_constraints: VDD18_A31: 1800 mV
[    0.300000] print_constraints: GPS_1V8: 1800 mV
[    0.300000] print_constraints: DVDD12: 1200 mV
[    0.305000] -s5m8767_pmic_probe()
[    0.305000] s5m87xx 1-0066: S5M87xx MFD probe done!!!
[    0.305000] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[    0.305000] s3c-i2c s3c2440-i2c.3: i2c-3: S3C I2C adapter
[    0.305000] s3c-i2c s3c2440-i2c.4: i2c-4: S3C I2C adapter
[    0.305000] s3c-i2c s3c2440-i2c.5: i2c-5: S3C I2C adapter
[    0.305000] s3c-i2c s3c2440-i2c.7: i2c-7: S3C I2C adapter
[    0.305000] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.305000] Bluetooth: Core ver 2.16
[    0.305000] NET: Registered protocol family 31
[    0.305000] Bluetooth: HCI device and connection manager initialized
[    0.305000] Bluetooth: HCI socket layer initialized
[    0.305000] Bluetooth: L2CAP socket layer initialized
[    0.305000] Bluetooth: SCO socket layer initialized
[    0.305000] cfg80211: Calling CRDA to update world regulatory domain
[    0.305000] Switching to clocksource mct-frc
[    0.306222] Switched to NOHz mode on CPU #0
[    0.306448] Switched to NOHz mode on CPU #3
[    0.306454] Switched to NOHz mode on CPU #1
[    0.306461] Switched to NOHz mode on CPU #2
[    0.315282] NET: Registered protocol family 2
[    0.315459] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.316060] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.317562] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.318366] TCP: Hash tables configured (established 131072 bind 65536)
[    0.318382] TCP reno registered
[    0.318397] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.318434] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.318705] NET: Registered protocol family 1
[    0.318914] PMU: registered new PMU device of type 0
[    0.319044] Exynos4 : ARM Clock down on idle mode is enabled
[    0.319893] regulator_consumer_probe: loading tc4-regulator-consumer
[    0.319913]  Register vdd_consumer_early_suspend done
[    0.320536] Loaded driver for PL330 DMAC-0 s3c-pl330
[    0.320553]  DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    0.320848] Loaded driver for PL330 DMAC-1 s3c-pl330
[    0.320864]  DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.320966] Loaded driver for PL330 DMAC-2 s3c-pl330
[    0.320981]  DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.339281] highmem bounce pool size: 64 pages
[    0.339493] ashmem: initialized
[    0.347590] fuse init (API version 7.16)
[    0.347921] msgmni has been set to 672
[    0.348527] io scheduler noop registered
[    0.348540] io scheduler deadline registered
[    0.348597] io scheduler cfq registered (default)
[    0.349461] value1 = 0, value2 = 0, type = 0x0
[    0.349479] (s3cfb_cfg_gpio, 84): BK_VDD_ON
[    0.450082] (s3cfb_cfg_gpio, 106): LCD_PWDN ON
[    0.454458]
[    0.454462]  CPU type:
[    0.454473]  Exynos 4412
[    0.454484] value1 = 0, value2 = 0, type = 0x0
[    0.464724] parent clock: 800000000, vclk: 65475000, vclk div: 12
[    0.714369] (s3cfb_backlight_on, 349): LCD_PWM_ON
[    0.719384] s3cfb s3cfb.0: registered successfully
[    0.720129] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.060270] s5pv210-uart.0: ttySAC0 at MMIO 0x13800000 (irq = 16) is a S3C6400/10
[    1.145064] s5pv210-uart.1: ttySAC1 at MMIO 0x13810000 (irq = 20) is a S3C6400/10
[    1.220061] s5pv210-uart.2: ttySAC2 at MMIO 0x13820000 (irq = 24) is a S3C6400/10
[    2.235220] console [ttySAC2] enabled
[    2.280061] s5pv210-uart.3: ttySAC3 at MMIO 0x13830000 (irq = 28) is a S3C6400/10
[    2.361010] SI GPS Initialize
[    2.362788] max485_ctl Initialize
[    2.366095] leds Initialize
[    2.368979] buzzer_ctl       initialized
[    2.372116] exynos_adc_probe, 124
[    2.375272] exynos_adc_probe, 134
[    2.378691] exynos_adc_probe, 136
[    2.381867] adc      initialized
[    2.391077] brd: module loaded
[    2.395814] loop: module loaded
[    2.397515] pmem: 0 init
[    2.400331] pmem_gpu1: 0 init
[    2.403618] i2c i2c-5: mpu_probe: 0
[    2.406438] i2c i2c-5: mpu_probe: irq:379
[    2.410427] <6>mldl_cfg:Reset MPU6050 B1
[    2.432665] mldl_cfg:Force to use default sensitivity(131,16384)
[    2.441320] i2c i2c-5: Installing irq using 379
[    2.444379] i2c i2c-5: Module Param interface = mpuirq
[    2.449795] i2c i2c-5: inv_mpu_register_slave: +mpu6050 Type 1: Addr: 68 IRQ: 379, Adapt:  5
[    2.458373] i2c i2c-5: Installing accelirq irq using 379
[    2.463380] i2c i2c-5: mpu_probe: init successfully.
[    2.468279] i2c-core: driver [mpu6050B1] using legacy suspend method
[    2.474509] i2c-core: driver [mpu6050B1] using legacy resume method
[    2.480765] mpu_init: Probe name mpu6050B1
[    2.485628] CAN device driver interface
[    2.488681] mcp251x: setup gpio pins CS and External Int
[    3.495064] mcp251x spi2.0: MCP251x didn't enter in conf mode after reset
[    3.500490] mcp251x spi2.0: Probe failed
[    3.504297] mcp251x spi2.0: probe failed
[    3.508358] PPP generic driver version 2.4.2
[    3.512807] smsc911x: Driver version 2008-10-21
[    3.517252] usbcore: registered new interface driver dm9601
[    3.522646] usbcore: registered new interface driver dm9620
[    3.528247] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.534692]
[    3.534695]
[    3.534698]  [usb_host_phy_init]++++++++++++++
[    3.542145] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[    3.547199] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[    3.554320] s5p-ehci s5p-ehci: irq 134, io mem 0x12580000
[    3.565031] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[    3.569063] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice=0300
[    3.577128] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.584329] usb usb1: New USB device Class: Class=9, SubClass=0, Protocol=0
[    3.591274] usb usb1: Product: S5P EHCI Host Controller
[    3.596479] usb usb1: Manufacturer: Linux 3.0.15 ehci_hcd
[    3.601860] usb usb1: SerialNumber: s5p-ehci
[    3.606653] hub 1-0:1.0: USB hub found
[    3.609841] hub 1-0:1.0: 3 ports detected
[    3.614462] usbcore: registered new interface driver cdc_acm
[    3.619479] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    3.627464] Initializing USB Mass Storage driver...
[    3.632470] usbcore: registered new interface driver usb-storage
[    3.638315] USB Mass Storage support registered.
[    3.643177] usbcore: registered new interface driver usbserial
[    3.648731] usbserial: USB Serial Driver core
[    3.653179] USB Serial support registered for GSM modem (1-port)
[    3.659209] usbcore: registered new interface driver option
[    3.664615] option: v0.7.2:USB Driver for GSM modems
[    3.669770] s3c-udc : S3C HS USB OTG Device Driver,(c) 2008-2009 Samsung Electronics
[    3.669775] s3c-udc : version 15 March 2009
[    3.683553] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    3.688966] android_usb gadget: Number of LUNs=3
[    3.693564]  lun0: LUN: removable file: (no medium)
[    3.698424]  lun1: LUN: removable file: (no medium)
[    3.703284]  lun2: LUN: removable file: (no medium)
[    3.708419] android_usb gadget: android_usb ready
[    3.713025] mousedev: could not register psaux device, error: -16
[    3.718909] mousedev: PS/2 mouse device common for all mice
[    3.725070] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    3.731826] input: samsung-keypad as /devices/platform/samsung-keypad/input/input1
[    3.739109] usbcore: registered new interface driver xpad
[    3.744206] usbcore: registered new interface driver usb_acecad
[    3.749983] acecad: v3.2:USB Acecad Flair tablet driver
[    3.755311] usbcore: registered new interface driver aiptek
[    3.760746] aiptek: v2.3 (May 2, 2007):Aiptek HyperPen USB Tablet Driver (Linux 2.6.x)
[    3.768642] aiptek: Bryan W. Headley/Chris Atenasio/Cedric Brun/Rene van Paassen
[    3.776136] usbcore: registered new interface driver gtco
[    3.781404] GTCO usb driver version: 2.00.0006
[    3.785771] usbcore: registered new interface driver hanwang
[    3.791588] usbcore: registered new interface driver kbtab
[    3.796941] kbtab: v0.0.2:USB KB Gear JamStudio Tablet driver
[    3.802787] usbcore: registered new interface driver wacom
[    3.808142] wacom: v1.52:USB Wacom tablet driver
[    3.813585] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[    3.818176] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[    3.823630] s3c_rtc_gettime() 2085-25-45 45:85:38
[    3.828639] using rtc device, s3c, for alarms
[    3.832465] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[    3.841605] s5m_rtc_read_time: 2012/1/1 1:47:38(0)
[    3.846015] s5m_rtc_read_alarm: 2000/0/1 0:0:0(-1)
[    3.851217] s5m_rtc_read_time: 2012/1/1 1:47:38(0)
[    3.854707] s5m-rtc s5m-rtc: rtc core: registered s5m-rtc as rtc1
[    3.861015] s5m-rtc s5m-rtc: RTC CHIP NAME: s5m-rtc
[    3.865587] i2c /dev entries driver
[    3.869936] Linux media interface: v0.10
[    3.873203] lirc_dev: IR Remote Control driver registered, major 251
[    3.879281] IR NEC protocol handler initialized
[    3.883792] IR RC5(x) protocol handler initialized
[    3.888565] IR RC6 protocol handler initialized
[    3.893079] IR JVC protocol handler initialized
[    3.897592] IR Sony protocol handler initialized

dubang12

[    3.902192] IR RC5 (streamzap) protocol handler initialized
[    3.907748] IR LIRC bridge handler initialized
[    3.912175] Linux video capture interface: v2.00
[    3.916876] ov5640_module_init
[    3.920620] s3c-csis: Samsung MIPI-CSIS0 driver probed successfully
[    3.926091] s3c-csis: Samsung MIPI-CSIS1 driver probed successfully
[    3.932431] Initialize JPEG driver
[    3.935956] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video12
[    3.942539] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video11
[    3.949265] i2c i2c-0: attached s5p_ddc into i2c adapter successfully
[    3.955601] i2c-core: driver [s5p_ddc] using legacy suspend method
[    3.961654] i2c-core: driver [s5p_ddc] using legacy resume method
[    3.967732] S5P HPD Driver, (c) 2009 Samsung Electronics
[    3.973413] S5P CEC Driver, (c) 2009 Samsung Electronics
[    3.979173] MFC(Multi Function Codec - FIMV v5.x) registered successfully
[    3.985546] Samsung Graphics 2D driver, (c) 2011 Samsung Electronics
[    3.991940] Mali: init_mali_clock mali_clock c090aec4
[    3.999260] Mali: failed to get cpufreq level for 1200MHzMali: Mali device driver  loaded
[    4.016284] usbcore: registered new interface driver uvcvideo
[    4.021797] USB Video Class driver (v1.1.0)
[    4.026089] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[    4.032176] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
[    4.040285] device-mapper: uevent: version 1.0.3
[    4.044436] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[    4.052550] Bluetooth: HCI UART driver ver 2.2
[    4.056953] Bluetooth: HCI H4 protocol initialized
[    4.061724] Bluetooth: HCI BCSP protocol initialized
[    4.066675] Bluetooth: HCILL protocol initialized
[    4.071359] Bluetooth: HCIATH3K protocol initialized
[    4.077004] cpuidle: using governor ladder
[    4.081405] cpuidle: using governor menu
[    4.084392] mshci: Mobile Storage Host Controller Interface driver
[    4.090456] mshci: Copyright (c) 2011 Samsung Electronics Co., Ltd
[    4.096720] clock source 0: sclk_dwmci (160000000 Hz)
[    4.101659] dw_mmc dw_mmc: clock source 0: sclk_dwmci (160000000 Hz)
[    4.108215] mmc0: Version ID 0x5342240a.
[    4.111896] mjdbg: cmu_max_clcok:800000000
[    4.115974] mjdbg: host->max_clk: 800000000
[    4.120358] mmc0: FIFO WMARK FOR RX 0x11 WX 0x1. ###########
[    4.127171] mmc0: MSHCI controller on samsung-mshci [dw_mmc] using IDMA
[    4.132568] sdhci: Secure Digital Host Controller Interface driver
[    4.138543] sdhci: Copyright(c) Pierre Ossman
[    4.141026] mmc0:mshci_set_clock, 400000@ration:4,11[mjdbg] cmu_set_clock: 400000
[    4.150420] s3c-sdhci s3c-sdhci.2: clock source 0: sclk_mmc (10666666 Hz)
[    4.155032] *******mmc0: inserted!!!!!******
[    4.161375] mmc0: cmd 52 response timeout error
[    4.166933] mmc1: no vmmc regulator found
[    4.169868] mmc0: cmd 52 response timeout error
[    4.175583] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[    4.181466] wake enabled for irq 359
[    4.185210] s3c-sdhci s3c-sdhci.3: clock source 0: sclk_mmc (10666666 Hz)
[    4.191753] mmc0: cmd 8 response timeout error
[    4.197210] sdhci_s3c_probe: set MMC_PM_IGNORE_PM_NOTIFY for mmc2 pm_flags
[    4.203036] mmc0: cmd 5 response timeout error
[    4.208466] sdhci_s3c_probe: set MMC_PM_KEEP_POWER | MMC_PM_WAKE_SDIO_IRQ for mmc2 pm_caps
[    4.215708] mmc0: cmd 5 response timeout error
[    4.221149] mmc2: no vmmc regulator found
[    4.224117] mmc0: cmd 5 response timeout error
[    4.229726] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[    4.235587] mmc0: cmd 5 response timeout error
[    4.241823] mmc0: cmd 55 response timeout error
[    4.246698] mmc0: cmd 55 response timeout error
[    4.251569] mmc0: cmd 55 response timeout error
[    4.256438] mmc0: cmd 55 response timeout error
[    4.269389] usbcore: registered new interface driver usbhid
[    4.273517] usbhid: USB HID core driver
[    4.277669] GPS: mt3326_gps_power: Switching GPS device on
[    4.282793] GPS: mt3326_gps_power: ignore power control: 1
[    4.288255] GPS: mt3326_gps_probe: Registering chardev
[    4.293379] GPS: mt3326_gps_probe: major: 249, minor: 0
[    4.298870] GPS: mt3326_gps_probe: Done
[    4.303712] Samsung Audio Subsystem Driver, (c) 2011 Samsung Electronics
[    4.309143] audss_init: RCLK SRC[busclk]
[    4.313816] mmc0:mshci_set_clock, 50000000@ration:4,11[mjdbg] cmu_set_clock: 50000000
[    4.332312] mmc0: new high speed DDR MMC card at address 0001
[    4.336920] mmcblk0: mmc0:0001 AWMB3R 14.5 GiB
[    4.342921]  mmcblk0: p1 p2 p3 p4
[    4.375062] *******mmc1: inserted!!!!!******
[    4.444512] asoc: wm8960-hifi <-> samsung-i2s.0 mapping ok
[    4.451313] asoc: wm8960-hifi <-> samsung-i2s.0 mapping ok
[    4.456326] Samsung SRP driver, (c) 2010 Samsung Electronics
[    4.470461] SRP: Driver successfully probed
[    4.473360] ALSA device list:
[    4.476139]   #0: iTOP-4412-Audio
[    4.479522] mmc1: new high speed SDHC card at address aaaa
[    4.485154] GACT probability NOT on
[    4.485271] mmcblk1: mmc1:aaaa SL16G 14.8 GiB
[    4.492843] Mirror/redirect action on
[    4.496462] u32 classifier
[    4.498006]  mmcblk1: p1 p2 p3 p4
[    4.502439]     Actions configured
[    4.505857] Netfilter messages via NETLINK v0.30.
[    4.510637] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    4.517468] ctnetlink v0.93: registering with nfnetlink.
[    4.521909] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    4.528824] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    4.534906] xt_time: kernel timezone is -0000
[    4.540352] ip_tables: (C) 2000-2006 Netfilter Core Team
[    4.544380] arp_tables: (C) 2002 David S. Miller
[    4.548922] TCP cubic registered
[    4.550059] *******mmc2: inserted!!!!!******
[    4.557186] NET: Registered protocol family 10
[    4.563838] Mobile IPv6
[    4.564828] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    4.570405] IPv6 over IPv4 tunneling driver
[    4.578539] NET: Registered protocol family 17
[    4.581545] NET: Registered protocol family 15
[    4.585948] can: controller area network core (rev 20090105 abi 8)
[    4.592178] NET: Registered protocol family 29
[    4.595068] *******mmc2: inserted!!!!!******
[    4.600795] can: raw protocol (rev 20090105)
[    4.606104] Bluetooth: RFCOMM TTY layer initialized
[    4.609896] Bluetooth: RFCOMM socket layer initialized
[    4.615028] Bluetooth: RFCOMM ver 1.11
[    4.618745] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    4.624050] Bluetooth: BNEP filters: protocol multicast
[    4.629278] NET: Registered protocol family 35
[    4.633920] EXYNOS4X12: Adaptive Support Voltage init
[    4.635089] *******mmc2: inserted!!!!!******
[    4.642983] EXYNOS4X12(SG):  ORIG : 3 MOD : 0 RESULT : 3
[    4.648271] EXYNOS4X12(SG):  ORIG : 3 MOD : 0 RESULT : 3
[    4.653567] ************ exynos4x12_set_abb:0x0, 0x0, 0x0, 0x0, 0x80000088
[    4.660419] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    4.668069] Registering SWP/SWPB emulation handler
[    4.672838] DVFS : VDD_ARM Voltage table set with 3 Group
[    4.675129] *******mmc2: inserted!!!!!******
[    4.682470] exynos4x12_cpufreq_init:topeet scp
[    4.687254] [ 302612 ] Memory Type Undertermined.
[    4.691587] DVFS : VDD_INT Voltage table set with 3 Group
[    4.760320] exynos4_integrated_dvfs_hotplug_init, max(1400000),min(200000)
[    4.769806] regulator_init_complete: VDD18_MIPI: incomplete constraints, leaving on
[    4.776477] regulator_init_complete: VDD10_MIPI: incomplete constraints, leaving on
[    4.784112] regulator_init_complete: VDD18_2M: incomplete constraints, leaving on
[    4.792931] regulator_init_complete: vdd_int range: incomplete constraints, leaving on
[    4.799856] regulator_init_complete: vdd_arm range: incomplete constraints, leaving on
[    4.807756] regulator_init_complete: vdd_mif range: incomplete constraints, leaving on
[    4.815686] USB_DEVICE_ATTACHED
[    4.919815] exynos_usb_Device: Exynos USB Device Driver
[    4.942332] ==ft5x0x_ts_init: reset==
[    5.145036] usb 1-3: new high speed USB device number 2 using s5p-ehci
[    5.280462] usb 1-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1a0
[    5.287090] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.294208] usb 1-3: New USB device Class: Class=9, SubClass=0, Protocol=2
[    5.301610] hub 1-3:1.0: USB hub found
[    5.304945] hub 1-3:1.0: 3 ports detected
[    5.460037] value1 = 0, value2 = 0, type = 0x0

dubang12

[    5.463210] input: ft5x0x_ts as /devices/virtual/input/input2
[    5.475573] ft5x0x_ts 3-0038: Firmware version 0x06
[    5.478976] ft5x0x_ts 3-0038: FocalTech ft5x0x TouchScreen initialized
[    5.486681] s5m_rtc_read_time: 2012/1/1 1:47:39(0)
[    5.490272] s3c_rtc_settime() 2012-1-1 1:47:39
[    5.494692] s5m_rtc_set_time: 2012/1/1 1:47:39(0)
[    5.525059] s5m-rtc s5m-rtc: setting system clock to 2012-01-01 01:47:39 UTC (1325382459)
[    5.532269] FIMC0 registered successfully
[    5.536207] FIMC1 registered successfully
[    5.540127] FIMC2 registered successfully
[    5.544092] FIMC3 registered successfully
[    5.548004] S5P TVOUT Driver v3.0 (c) 2010 Samsung Electronics
[    5.590254] usb 1-3.2: new high speed USB device number 3 using s5p-ehci
[    5.700470] usb 1-3.2: config 1 interface 0 altsetting 0 endpoint 0x83 has an invalid bInterval 0, changing to 9
[    5.790009] usb 1-3.2: New USB device found, idVendor=0a46, idProduct=9621, bcdDevice=0101
[    5.799481] usb 1-3.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    5.807048] usb 1-3.2: New USB device Class: Class=0, SubClass=0, Protocol=0
[    5.815470] dm962x: dm_read_reg() 0x29 0x0a
[    5.818346] dm962x: dm_read_reg() 0x28 0x46
[    5.825340] dm962x: dm_read_reg() 0x2b 0x96
[    5.828456] dm962x: dm_read_reg() 0x2a 0x21
[    5.832697] dm962x: dm_read_reg() 0xF2 0x00
[    5.836556] dm962x:  [Analysis.2] 0xF2, D[7] 0 OK
[    5.841874] dm962x:  [Analysis.2] 0xF2, D[6] 0 OK
[    5.845793] dm962x:  [Analysis.2] 0xF2, D[5] 0 EP1: Empty
[    5.851176] dm962x:  [Analysis.2] 0xF2, D[3] 0 OK
[    5.855917] dm962x:  [Analysis.2] 0xF2, D[2] 0 OK
[    5.860605] dm962x:  [Analysis.2] 0xF2, D[1] 0 OK
[    5.865242] dm962x:  [Analysis.2] 0xF2, D[0] 0 Status: TX buffer 0 pkts
[    5.882232] dm962x: ethernet MAC address 00:00:ff:ff:00:00 (chip)
[    5.889353] dm962x: 9620 Mode = 128
[    5.920814] dm9620 1-3.2:1.0: eth0: register 'dm9620' at usb-s5p-ehci-3.2, Davicom DM9620 USB Ethernet, 00:00:ff:ff:00:00
[    6.675020] CPU1: shutdown
[    7.223761] CPU2: shutdown
[    7.880673] EXT4-fs (mmcblk1p2): warning: checktime reached, running e2fsck is recommended
[    7.891737] EXT4-fs (mmcblk1p2): 3 orphan inodes deleted
[    7.895681] EXT4-fs (mmcblk1p2): recovery complete
[    7.936731] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
[    7.943555] VFS: Mounted root (ext4 filesystem) on device 179:10.
[    7.949771] Freeing init memory: 220K
[    7.954619] Failed to execute /linuxrc.  Attempting defaults...
mountall: Event failed
* Starting bluetooth daemon                                             [ OK ]
* Starting mDNS/DNS-SD daemon                                           [ OK ]
* Starting network connection manager                                   [ OK ]
* Starting load fallback graphics devices                               [ OK ]
* Starting Userspace bootsplash                                         [ OK ]
* Stopping load fallback graphics devices                               [ OK ]
[   20.678435] init: Failed to create pty - disabling logging for job
[   20.813302] init: Failed to create pty - disabling logging for job
[   20.826390] init: Failed to create pty - disabling logging for job
[   21.556228] init: Failed to create pty - disabling logging for job
[   21.568543] init: Failed to create pty - disabling logging for job
[   22.184224] init: Failed to create pty - disabling logging for job
[   22.207609] init: Failed to create pty - disabling logging for job
[   22.216300] init: Failed to create pty - disabling logging for job
[   22.226505] init: Failed to create pty - disabling logging for job
[   22.238016] init: Failed to create pty - disabling logging for job
[   22.337589] init: Failed to create pty - disabling logging for job
[   22.345332] init: Failed to create pty - disabling logging for job

speech-dispatcher disabled; edit /etc/default/speech-dispatcher
[   22.374040] init: Failed to create pty - disabling logging for job
saned disabled; edit /etc/default/saned
[   22.452488] init: Failed to create pty - disabling logging for job
[   22.459730] init: Failed to create pty - disabling logging for job
[   22.472693] init: Failed to create pty - disabling logging for job
[   22.480175] init: Failed to create pty - disabling logging for job
[   22.490457] init: Failed to create pty - disabling logging for job
Last login: Sun Jan  1 01:32:06 UTC 2012 on tty1
[   22.534659] init: Failed to create pty - disabling logging for job
[   22.593405] init: Failed to create pty - disabling logging for job
[   22.689478] init: Failed to create pty - disabling logging for job
[   22.727521] init: Failed to create pty - disabling logging for job
Welcome to Linaro 12.04 (GNU/Linux 3.0.15 armv7l)

* Documentation:  http s://wiki.linar o.o rg/

0 packages can be updated.
0 updates are security updates.

0 packages can be updated.
0 updates are security updates.

0 packages can be updated.
0 updates are security updates.

root@iTOP4412-ubuntu-desktop:~

dubang12

上面的是系统启动时的串口数据

dubang12

启动后输入df -l只有TF卡的盘没有emmc的用fdisk -l可以找到2个盘
root@iTOP4412-ubuntu-desktop:~# df -l
Filesystem     1K-blocks    Used Available Use% Mounted on
/dev/root        2721368 2030984    552144  79% /
none              827200       4    827196   1% /dev
none              165444     672    164772   1% /run
none                5120       0      5120   0% /run/lock
none              827200      24    827176   1% /run/shm
root@iTOP4412-ubuntu-desktop:~# fdisk -l

Disk /dev/mmcblk0: 15.6 GB, 15634268160 bytes
255 heads, 63 sectors/track, 1900 cylinders, total 30535680 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

        Device Boot      Start         End      Blocks   Id  System
/dev/mmcblk0p1         6791168    30515199    11862016    c  W95 FAT32 (LBA)
/dev/mmcblk0p2           32768     5562367     2764800   83  Linux
/dev/mmcblk0p3         5562368     6176767      307200   83  Linux
/dev/mmcblk0p4         6176768     6791167      307200   83  Linux

Partition table entries are not in disk order

Disk /dev/mmcblk1: 15.9 GB, 15931539456 bytes
255 heads, 63 sectors/track, 1936 cylinders, total 31116288 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

        Device Boot      Start         End      Blocks   Id  System
/dev/mmcblk1p1         5767168    31095807    12664320    c  W95 FAT32 (LBA)
/dev/mmcblk1p2           32768     5562367     2764800   83  Linux
/dev/mmcblk1p3         5562368     5664767       51200   83  Linux
/dev/mmcblk1p4         5664768     5767167       51200   83  Linux

dubang12

过了一会系统就会自动跑起来然后报错
Partition table entries are not in disk order
[  471.906891] EXT4-fs (mmcblk1p2): previous I/O error to superblock detected
[  471.913788] mmc1: ADMA error
[  471.916701] mmcblk1: error -110 sending read/write command, response 0x0, card status 0x400d00
[  471.925200] mmcblk1: error -5 transferring data, sector 32768, nr 8, card status 0x400d00
[  471.933708] EXT4-fs error (device mmcblk1p2): ext4_map_blocks:1301: inode #211727: block 417108: comm ubuntuone-insta: lblock 0 mapped to illegal pblock (length 1)
[  471.947993] EXT4-fs (mmcblk1p2): previous I/O error to superblock detected
[  471.954845] mmc1: ADMA error
[  471.957732] mmcblk1: error -110 sending read/write command, response 0x0, card status 0x400d00
[  471.966255] mmcblk1: error -5 transferring data, sector 32768, nr 8, card status 0x400d00
[  471.974763] EXT4-fs error (device mmcblk1p2): ext4_map_blocks:1301: inode #211727: block 417108: comm ubuntuone-insta: lblock 0 mapped to illegal pblock (length 1)
[  471.989007] EXT4-fs (mmcblk1p2): previous I/O error to superblock detected

dubang12

屏幕按键以后会报错：
[  472.119133] mmc1: ADMA error
[  472.121936] mmcblk1: error -110 sending read/write command, response 0x0, card status 0x400d00
[  472.130537] mmcblk1: error -5 transferring data, sector 32768, nr 8, card status 0x400d00
[  472.139031] Buffer I/O error on device mmcblk1p2, logical block 0
[  472.144744] EXT4-fs error (device mmcblk1p2): ext4_map_blocks:1301: inode #211727: block 417108: comm ubuntuone-insta: lblock 0 mapped to illegal pblock (length 1)
[  472.159308] EXT4-fs (mmcblk1p2): previous I/O error to superblock detected
[  472.166209] mmc1: ADMA error
[  472.169057] mmcblk1: error -110 sending read/write command, response 0x0, card status 0x400d00
[  472.177670] mmcblk1: error -5 transferring data, sector 32768, nr 8, card status 0x400d00
[  472.186118] Buffer I/O error on device mmcblk1p2, logical block 0
[  472.191876] EXT4-fs error (device mmcblk1p2): ext4_map_blocks:1301: inode #211727: block 417108: comm ubuntuone-insta: lblock 0 mapped to illegal pblock (length 1)
[  472.206477] EXT4-fs (mmcblk1p2): previous I/O error to superblock detected

dubang12

这是使用的TF卡
这是拨码