请选择 进入手机版 | 继续访问电脑版
搜索

1

主题

2

帖子

14

积分

新手上路

Rank: 1

积分
14
发表于 2021-8-23 13:43:49 3393 浏览 2 回复

TF卡烧写linux-QT时,使用光盘给出的uboot、内核、文件系统。无限重启

本帖最后由 wangcheng 于 2021-8-23 13:45 编辑

U-Boot 2010.03 (Mar 20 2018 - 00:02:39) for iTOP-4412 Android

        APLL = 1000MHz, MPLL = 800MHz
        ARM_CLOCK = 1000MHz
PMIC:   S5M8767(VER5.0)
Board:  iTOP-4412
DRAM:    1 GB
MMC:   max_emmc_clock:40 MHZ
Set CLK to 400 KHz
EMMC CLOCK OUTPUT:: 400KHz -[div:50]
response timeout error : 00000104 cmd 8
response timeout error : 00000104 cmd 55
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
MMC0:   7456 MB
SD sclk_mmc is 400K HZ
raise: Signal # 8 caught
raise: Signal # 8 caught
MMC1:   0 MB
0 MB
*** Warning - using default environment

In:    serial
Out:   serial
Err:   serial
eMMC OPEN Success.!!
                        !!!Notice!!!
!You must close eMMC boot Partition after all image writing!
!eMMC boot partition has continuity at image writing time.!
!So, Do not close boot partition, Before, all images is written.!

MMC read: dev # 0, block # 48, count 16 ...16 blocks read: OK
eMMC CLOSE Success.!!


Checking Boot Mode ... EMMC4.41
SYSTEM ENTER NORMAL BOOT MODE
Hit any key to stop autoboot:  0
reading kernel.. 1120, 12288
MMC read: dev # 0, block # 1120, count 12288 ...12288 blocks read: OK
completed
Boot with zImage
Wrong Ramdisk Image Format
[err] boot_get_ramdisk

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
OK

U-Boot 2010.03 (Mar 20 2018 - 00:02:39) for iTOP-4412 Android

        APLL = 1000MHz, MPLL = 800MHz
        ARM_CLOCK = 1000MHz
PMIC:   S5M8767(VER5.0)
Board:  iTOP-4412
DRAM:    1 GB
MMC:   max_emmc_clock:40 MHZ
Set CLK to 400 KHz
EMMC CLOCK OUTPUT:: 400KHz -[div:50]
response timeout error : 00000104 cmd 8
response timeout error : 00000104 cmd 55
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
MMC0:   7456 MB
SD sclk_mmc is 400K HZ
raise: Signal # 8 caught
raise: Signal # 8 caught
MMC1:   0 MB
0 MB
*** Warning - using default environment

In:    serial
Out:   serial
Err:   serial
eMMC OPEN Success.!!
                        !!!Notice!!!
!You must close eMMC boot Partition after all image writing!
!eMMC boot partition has continuity at image writing time.!
!So, Do not close boot partition, Before, all images is written.!

MMC read: dev # 0, block # 48, count 16 ...16 blocks read: OK
eMMC CLOSE Success.!!


Checking Boot Mode ... EMMC4.41
SYSTEM ENTER NORMAL BOOT MODE
Hit any key to stop autoboot:  0
reading kernel.. 1120, 12288
MMC read: dev # 0, block # 1120, count 12288 ...12288 blocks read: OK
completed
Boot with zImage
Wrong Ramdisk Image Format
[err] boot_get_ramdisk

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0.15 (root@cym-virtual-machine) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #6 SMP PREEMPT Mon Jun 4 15:09:07 CST 2018
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: SMDK4X12
[    0.000000] NR_BANKS too low, ignoring high memory
[    0.000000] **************************
[    0.000000] reserve_panic_dump_area!!
[    0.000000] **************************
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU EXYNOS4412 (id 0xe4412011)
[    0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[    0.000000] s3c_register_clksrc: clock audiocdclk has no registers set
[    0.000000] audiocdclk: no parent clock specified


请大神们帮忙看下什么原因 如何解决
回复

使用道具 举报

0

主题

30

帖子

8215

积分

版主

Rank: 7Rank: 7Rank: 7

积分
8215

活跃会员热心会员推广达人宣传达人灌水之王突出贡献优秀版主荣誉管理论坛元老

发表于 2021-8-23 14:08:42
光盘资料下载链接:https://pan.baidu.com/s/1zQuoZZ6vyxrcrFlFABiPaA
提取码:llko
网盘资料链接:链接:https://pan.baidu.com/s/1mkNLnvFw9W7L4bI1Nx56wg
提取码:tesq
使用最新的资料再烧写试试
回复 点赞

使用道具 举报

1

主题

2

帖子

14

积分

新手上路

Rank: 1

积分
14
 楼主| 发表于 2021-8-23 15:43:23
AppleLinux 发表于 2021-8-23 14:08
光盘资料下载链接:https://pan.baidu.com/s/1zQuoZZ6vyxrcrFlFABiPaA
提取码:llko
网盘资料链接:链 ...

谢谢我尝试下
回复 点赞

使用道具 举报

返回列表
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

登录或注册

官方客服

QQ:2551456065

官方QQ群

195631883

扫一扫关注迅为公众号

群号652692981

 
快速回复 返回顶部 返回列表