TF卡烧写linux-QT时，使用光盘给出的uboot、内核、文件系统。无限重启

wangcheng · 发表于 2021-8-23 13:43:49

本帖最后由 wangcheng 于 2021-8-23 13:45 编辑

U-Boot 2010.03 (Mar 20 2018 - 00:02:39) for iTOP-4412 Android

      APLL = 1000MHz, MPLL = 800MHz
      ARM_CLOCK = 1000MHz
PMIC: S5M8767(VER5.0)
Board:  iTOP-4412
DRAM: 1 GB
MMC: max_emmc_clock:40 MHZ
Set CLK to 400 KHz
EMMC CLOCK OUTPUT:: 400KHz -[div:50]
response timeout error : 00000104 cmd 8
response timeout error : 00000104 cmd 55
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
MMC0: 7456 MB
SD sclk_mmc is 400K HZ
raise: Signal # 8 caught
raise: Signal # 8 caught
MMC1: 0 MB
0 MB
*** Warning - using default environment

In: serial
Out: serial
Err: serial
eMMC OPEN Success.!!
                     !!!Notice!!!
!You must close eMMC boot Partition after all image writing!
!eMMC boot partition has continuity at image writing time.!
!So, Do not close boot partition, Before, all images is written.!

MMC read: dev # 0, block # 48, count 16 ...16 blocks read: OK
eMMC CLOSE Success.!!

Checking Boot Mode ... EMMC4.41
SYSTEM ENTER NORMAL BOOT MODE
Hit any key to stop autoboot:  0
reading kernel.. 1120, 12288
MMC read: dev # 0, block # 1120, count 12288 ...12288 blocks read: OK
completed
Boot with zImage
Wrong Ramdisk Image Format
[err] boot_get_ramdisk

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
OK

U-Boot 2010.03 (Mar 20 2018 - 00:02:39) for iTOP-4412 Android

      APLL = 1000MHz, MPLL = 800MHz
      ARM_CLOCK = 1000MHz
PMIC: S5M8767(VER5.0)
Board:  iTOP-4412
DRAM: 1 GB
MMC: max_emmc_clock:40 MHZ
Set CLK to 400 KHz
EMMC CLOCK OUTPUT:: 400KHz -[div:50]
response timeout error : 00000104 cmd 8
response timeout error : 00000104 cmd 55
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
MMC0: 7456 MB
SD sclk_mmc is 400K HZ
raise: Signal # 8 caught
raise: Signal # 8 caught
MMC1: 0 MB
0 MB
*** Warning - using default environment

In: serial
Out: serial
Err: serial
eMMC OPEN Success.!!
                     !!!Notice!!!
!You must close eMMC boot Partition after all image writing!
!eMMC boot partition has continuity at image writing time.!
!So, Do not close boot partition, Before, all images is written.!

MMC read: dev # 0, block # 48, count 16 ...16 blocks read: OK
eMMC CLOSE Success.!!

Checking Boot Mode ... EMMC4.41
SYSTEM ENTER NORMAL BOOT MODE
Hit any key to stop autoboot:  0
reading kernel.. 1120, 12288
MMC read: dev # 0, block # 1120, count 12288 ...12288 blocks read: OK
completed
Boot with zImage
Wrong Ramdisk Image Format
[err] boot_get_ramdisk

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.15 (root@cym-virtual-machine) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #6 SMP PREEMPT Mon Jun 4 15:09:07 CST 2018
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: SMDK4X12
[ 0.000000] NR_BANKS too low, ignoring high memory
[ 0.000000] **************************
[ 0.000000] reserve_panic_dump_area!!
[ 0.000000] **************************
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU EXYNOS4412 (id 0xe4412011)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] s3c_register_clksrc: clock audiocdclk has no registers set
[ 0.000000] audiocdclk: no parent clock specified

请大神们帮忙看下什么原因如何解决