|
|
发表于 2020-11-8 19:25:12
13002 浏览 4 回复
TF卡烧写QT时，TF卡只少了0.9G
在测试TF卡烧写QT时，虽然提示-“-iTOP-4412.bin image has been fused successfully”，但是TF卡只少了0.9G，下面的操作就失败！我换了不同的TF和读卡器，基本上都只少了0.9G！我做好了好多遍了，感觉是哪个地方遗漏了，请问，这个问题需要怎么排查？
|
|
|
|
|
|
|
|
|
|
|
|
|
只少？还是只烧？ 看看能不能运行呢，具体是怎么操作的 |
|
|
|
|
|
|
|
|
|
|
|
楼主|
发表于 2020-11-10 19:57:25
我做“视频10_03TF卡烧写Qt”和“视频10_04开发板出厂前首次烧写”这两个，在制作TF卡的时候，ubuntu的终端会提示“u-boot-iTOP-4412.bin image has been fused successfully”，但是查看TF卡容量的变化，我的TF卡容量只少了0.9G，没有像资料中提示的少2G左右的空间！然后设置开发板从TF卡启动，进入Uboot后执行“sdfuse flashall”，这时就报错了！
OK
U-Boot 2010.03 (May 17 2017 - 11:13:23) for iTOP-4412 Android
APLL = 1000MHz, MPLL = 800MHz
ARM_CLOCK = 1000MHz
PMIC: S5M8767(VER5.0)
Board: iTOP-4412
DRAM: 1 GB
MMC: max_emmc_clock:40 MHZ
Set CLK to 400 KHz
EMMC CLOCK OUTPUT:: 400KHz -[div:50]
response timeout error : 00000104 cmd 8
response timeout error : 00000104 cmd 55
unrecognised EXT_CSD structure version 8
[ERROR]Card init fail,so Change mode and try again..!
[ERROR]go to inital again..!
FAIL: waiting for status update.
[ERROR]Card init fail again..So give up mmc initial!
MMC0: 1024 MB
SD sclk_mmc is 400K HZ
SD sclk_mmc is 50000K HZ
SD sclk_mmc is 50000K HZ
MMC1: 29580 MB
*** Warning - using default environment
In: serial
Out: serial
Err: serial
Checking Boot Mode ... SDMMC
SYSTEM ENTER NORMAL BOOT MODE
Hit any key to stop autoboot: 0
reading kernel.. 1120, 12288
MMC read: dev # 1, block # 1120, count 12288 ...12288 blocks read: OK
completed
Wrong Image Format for bootm command
ERROR: can't get kernel image!
iTOP-4412 # sdfuse flashall
SD sclk_mmc is 400K HZ
SD sclk_mmc is 50000K HZ
SD sclk_mmc is 50000K HZ
[Fusing Image from SD Card.]
.FAIL: waiting for status update.
mmc write failed
there are pending interrupts 0x10,11
FAIL: waiting for status update.
mmc read failed
>>>part_type : 0
there are pending interrupts 0x830,11
FAIL: waiting for status update.
mmc read failed
** Can't read from device 0 **
fatformat failed for part_no:1
** sd_format_mmcs failed **
*****************************
Booting Device Initial Fail!
*****************************
iTOP-4412 # |
|
|
|
|
|
|
|
|
|
|
|
楼主|
发表于 2020-11-11 08:52:51
我做“视频10_03TF卡烧写Qt”和“视频10_04开发板出厂前首次烧写”这两个，在制作TF卡的时候，ubuntu的终端会提示“u-boot-iTOP-4412.bin image has been fused successfully”，但是查看TF卡容量的变化，我的TF卡容量只少了0.9G，没有像资料中提示的少2G左右的空间！然后设置开发板从TF卡启动，进入Uboot后执行“sdfuse flashall”，这时就报错了！
OK
U-Boot 2010.03 (May 17 2017 - 11:13:23) for iTOP-4412 Android
APLL = 1000MHz, MPLL = 800MHz
ARM_CLOCK = 1000MHz
PMIC: S5M8767(VER5.0)
Board: iTOP-4412
DRAM: 1 GB
MMC: max_emmc_clock:40 MHZ
Set CLK to 400 KHz
EMMC CLOCK OUTPUT:: 400KHz -[div:50]
response timeout error : 00000104 cmd 8
response timeout error : 00000104 cmd 55
unrecognised EXT_CSD structure version 8
[ERROR]Card init fail,so Change mode and try again..!
[ERROR]go to inital again..!
FAIL: waiting for status update.
[ERROR]Card init fail again..So give up mmc initial!
MMC0: 1024 MB
SD sclk_mmc is 400K HZ
SD sclk_mmc is 50000K HZ
SD sclk_mmc is 50000K HZ
MMC1: 29580 MB
*** Warning - using default environment
In: serial
Out: serial
Err: serial
Checking Boot Mode ... SDMMC
SYSTEM ENTER NORMAL BOOT MODE
Hit any key to stop autoboot: 0
reading kernel.. 1120, 12288
MMC read: dev # 1, block # 1120, count 12288 ...12288 blocks read: OK
completed
Wrong Image Format for bootm command
ERROR: can't get kernel image!
iTOP-4412 # sdfuse flashall
SD sclk_mmc is 400K HZ
SD sclk_mmc is 50000K HZ
SD sclk_mmc is 50000K HZ
[Fusing Image from SD Card.]
.FAIL: waiting for status update.
mmc write failed
there are pending interrupts 0x10,11
FAIL: waiting for status update.
mmc read failed
>>>part_type : 0
there are pending interrupts 0x830,11
FAIL: waiting for status update.
mmc read failed
** Can't read from device 0 **
fatformat failed for part_no:1
** sd_format_mmcs failed **
*****************************
Booting Device Initial Fail!
*****************************
iTOP-4412 # |
|
|
|
|
|
|
|
|
|
登录或注册
扫一扫关注迅为公众号
|
